المحرر موضوع: لإصلاح الغسالات في دبي  (زيارة 51 مرات)

0 الأعضاء و 1 ضيف يشاهدون هذا الموضوع.

غير متصل kmalramisamer

  • عضو مميز
  • ****
  • مشاركة: 1220
  • منتديات عنكاوا
    • مشاهدة الملف الشخصي
لإصلاح الغسالات في دبي
« في: 19:31 01/10/2019 »
    Al Quoz Third Dubai Washing Machine Repair

    A Complete Guide to Repair Washing Machine PCB
    Steps to Repair Washing Machine PCB
    Let'a give you the step by step instructions on it!
    • It is to be   mentioned that in the starting the front loader washer must be empty   before you can open the door to work on it. You need to make sure   all screws and components are tight. For the information of the   readers, we would like to mention that washing machine is all known   as the big tub that repeatedly fills with water and then drains. It   does spins to wring clothes dry. It also accompanies the device for   stirring the contents up that is either an agitator in the middle of   a top-load machine or a rolling drum in a front-loading machine.
    • After it, the four   cycles in the washing machine will be performing the task of the   fill, wash, drain, and spin. These functions are basic in any   washing machine so there are a few numbers of things can go wrong   with them. Al   Quoz Third Dubai Washing Machine Repair
    • If the washer does   not operate or make any noise when set on any cycle, then it is   possible that it is not receiving electrical power.
    • If the washing   machine stopped at the time when it has to be continued on to the   next cycle, then the machine's overload protector may have   tripped. You have to out some of the articles to reduce the load and   let the protector reset itself. After it, you can restart the   machine.
    • You have to make   sure the machine is plugged in and turned on. If not, then you have   to check the receptacle as it has to be plugged into for power. This   can be all done as by using a working lamp, or the appliance, or   voltage tester. You do need to make sure that the washer lid is   closed completely.
    • If in the condition   the receptacle seems dead, then you should check the circuit breaker   or the fuse that serves it.
    • You should also   check the power cord. You have to unplug the washer and then check   its cord as in favor of the break or frayed area. If you do find it   important then you can replace the cord. Al   Karama Dubai Washing Machine Repair
    • You have to open   with the lid and then check the lid switch and the tab on the lid   that it pushes as against. You have to press and release the switch.   If still, it is not working then it means that it has been broken.   You should remove the switch, test it, and replace it if needed.
    • If the washer still   does not work, the controls may be the fault in it. You should take   help from the appliance repair person.
    If you want to prevent some of the problems of the washing machine, then you should follow up with some of the best maintenance procedures.
    You should make the use of the right amount of detergent for your washer and your water hardness. You do need to make sure the machine is level, and don't overload it.
    What to do if Washing Machine Does Not Rinse Correctly?
    If there is some residue that is on your clothes or in the washing machine following a cycle, then this can be because of so many reasons. First of all, you have to make sure that you are using the machine properly.
    You should be putting the right amount of soap in the load and not be overloading the machine. This is for the reason that the overly bulky load can cause improper rinsing.
    If these types of issues are not leading to any problem, then there are chances that the water is not getting into the drum or is not draining out properly. You should be checking the supply valves. Al Qusais First Dubai Washing Machine Repair
    You should make sure the water supply valves that serve the supply hoses are open all the way. You should also make sure that the supply hoses are not kinked.
    You can also give a check on the drain hose to make sure the machine is draining fully.